![]() It's not about the hardware in your rig, but the software in your heart! You don't necessarily need a PC to be a member of the PCMR.This includes build help, tech support, and any kind of doubt one might have about PC ownership. Every kind of PC related content is welcome here.Everybody is welcome here, even those that have yet to ascend.Begin your ascension today! General Information Please like and share this guide to help others.Official Subreddit of the PC Master Race We're the largest community of PC enthusiasts on the Internet. That's it! Let me know if this guide has helped you by leaving your comment about your experience. If the disk is damaged, then replace the disk. Check the hard disk for problems, by using the instructions on this article: Best Hard Drive Test & Diagnostic Tools to Check Hard Disk’s Health. If the "The parameter is incorrect" error is occurred when you try to format an SD card, then use the SD Card Formatter tool.ģ. If the "The parameter is incorrect" error is occurred when you try to format a USB disk, try to format the disk by using the: HP USB Disk Storage Format Tool.Ģ. Other methods to fix the "The parameter is incorrect" error in DISKPART.ġ. ![]() * Note: If you have a disk over 2TB, then use the convert gpt command instead. * Note: If you found, more than one volumes on the selected disks, then "select" and "delete" all of them (one by one). * Note: Where "X" is the volume number that the selected disk contains. * Note: The "detail disk" command shows only the volume(s) of the selected disk. – Try to delete all volumes on the disk and then specify the partition structure type (MBR or GPT) by following the procedure below: * Note: The "clean all" command should take some time, so be patient. – Run DiskPart again and replace the clean command with clean all and instead of the format fs=ntfs quick command type format fs=ntfs (without quick). – If after following the above procedure, you still receive the "DiskPart has encountered an error: The parameter is incorrect" error then continue to next method below. Finally type exit and press Enter to close DiskPart tool. Finally format the select partition, using the following command and press Enter:Ĩ. Now give the following command to select the created partition and press Enter:ħ. When the "Clean" is completed, type the following command to create a partition on the disk and press Enter:Ħ. Then type the following command to totally erase the disk and press Enter. * Note: Where "X" is the disk number of the disk that you want to format. the "disk 1" in this example) and then type the following command to select the disk by using it's number (e.g. Carefully locate the disk that you want to format (e.g. Type the following command to list all the available drives and press Enter:ģ. In command Prompt type: diskpart and press Enter.Ģ. – To resolve the "DiskPart has encountered an error: The parameter is incorrect" error after running the " format fs=ntfs" command in DISKPART utility, try the following steps: Method 1.ġ. Don't forget to launch Command Prompt with Administrative privileges, in order to run DiskPart. Carefully select the drive (disk) that you want to format to avoid losing your data.ģ. Before you continue, unplug all unneeded storage devices from your computer (USB disks, Memory cards, etc.).Ģ. ![]() How to FIX: DiskPart has encountered an error: The parameter is incorrectġ. In this tutorial you 'll find detailed instructions on how to resolve the "DiskPart has encountered an error: The parameter is incorrect" error. For example, if you have a Hard Disk, a USB Flash Drive or an SD Card that cannot be formatted or accessed by Windows due to data corruption or other issues, you can use the DiskPart tool to format the disk.ĭiskPart tool must be used very carefully, because it can ERASE everything on the selected hard drive, so before using it make sure that you already have a backup of your data to another storage media. DiskPart is a powerful disk utility which is commonly used to manage disks, partitions, or volumes that cannot be managed using Windows Disk Manager options. The error is appeared after the format process reaches the 100%, without an obvious reason. "DiskPart has encountered an error: The parameter is incorrect" error can be occurred when you try to format a drive using the "format fs=ntfs" command using DiskPart tool.
0 Comments
Leave a Reply. |